Fast, Reliable Gate Parts & Welding Across Kensington
Gate parts and welding repair in Kensington, NY typically runs $180-$650 depending on whether you need a simple hinge replacement or custom fabrication for obsolete wrought-iron hardware. Most jobs are completed in a single visit, with same-day service available when you call before noon. If your century-old front gate is dragging on the stoop or your shared side-yard passage has a seized hinge, our Gate Parts & Welding team can usually restore it without replacing the whole assembly.
We’ve been working on Kensington’s early-20th-century ironwork for over 42 years. The neighborhood’s brick semi-detached rowhouses on narrow 20-25 foot lots, built mostly between 1900 and 1930, present a specific kind of gate problem: small ornamental pedestrian gates and side-yard passages integrated into low iron fencing along shared property lines. These aren’t freestanding driveway gates. They’re legacy ironwork, often original to the house, and they require a repair approach that respects both the metal and the masonry it’s embedded in.
We answer calls 24 hours a day, 7 days a week. A live person picks up. No voicemail trees. From our base in New York City, we’re typically on Beverley Road, Cortelyou Road, or Ocean Parkway within the hour for urgent calls. Dial (877) 326-7055.
Why Ironworks Gate Co. of New York City Is Kensington’s Preferred Gate Parts & Welding Company
Kensington homeowners know the difference between a handyman who’ll slap on a hardware-store hinge and a craftsperson who understands how a 1920s wrought-iron gate was originally built. We’ve earned that trust block by block, from the semi-detached pairs along Albemarle Road to the attached rows near Prospect Park Southwest.
Our reputation here is built on specificity. When a Kensington customer calls about a dragging gate, we already know to ask about mortar cracks in the stoop post, because we’ve seen what NYC’s freeze-thaw cycles do to masonry-embedded hardware. We know that salt on Brooklyn sidewalks accelerates rust on original iron in ways that suburban gates never experience. That local knowledge means faster diagnosis and fewer return trips.
We’re on time. We say what the job will cost before we start. And every repair, every weld, every part replacement carries our written 90-Day Done Right Promise - the Keystone Standard. If it’s not right, we come back and make it right. No paperwork, no arguing, no exceptions. Frank Delmonico established that standard when he founded Ironworks Gate Co. in 1984, and it applies to the 400th job exactly as it did to the first.
Our Gate Parts & Welding Services in Kensington
Hinge Replacement
Original wrought-iron hinge pins on Kensington’s century-old gates wear out from decades of freeze-thaw expansion against brick and mortar. The gate sags, binds against the stoop, and eventually seizes completely. We stock modern equivalents that match original specifications, and when the part is obsolete - common on pre-1950 forged-iron designs - we fabricate a replacement in our mobile welding rig. A typical hinge replacement in Kensington runs $180-$320, including alignment adjustment to compensate for settled posts.
Post Replacement
Masonry gate posts embedded in Kensington stoops and front walls crack and shift as temperatures cross 32°F repeatedly each winter. A new post isn’t always possible without disturbing the stoop, so we often install steel sleeves set in structural epoxy, anchored to sound masonry above and below the damaged section. This preserves the original brickwork while giving the hinge a solid, plumb mounting surface. Post repair or replacement in Kensington typically costs $280-$480.
Rail Repair & Custom Welding
Decorative iron scrollwork on century-old gates cracks at weld joints from repeated opening against misaligned posts. We can weld these cracks in place without removing the entire gate, using portable TIG equipment and color-matched filler rod that blends with aged iron. For rails that are too far gone, we fabricate replacements to match existing patterns. Custom welding and rail repair in Kensington generally runs $340-$650 depending on access and pattern complexity.
Gate Rollers, Latch & Lock
Shared side-yard gates between Kensington’s semi-detached units take constant use from multiple households and develop latch alignment issues when one owner installs a new storm door or siding that shifts the post. We realign, replace, or upgrade latches and locks, including compatibility with existing access control systems. Latch and lock service in Kensington typically runs $150-$280. Roller replacement for sliding gates, less common here but present on some wider driveways near Ocean Parkway, runs $200-$350.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Trusted Brands We Service in Kensington
We carry parts and provide certified service for nine major gate-automation brands: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. For Kensington’s older housing stock, this matters most when a homeowner inherits a discontinued opener or keypad and needs a part that hasn’t been manufactured in years. We maintain a stock of legacy components for DoorKing and Elite systems commonly installed in Brooklyn during the 1990s and 2000s, and we can often source or fabricate alternatives for Mighty Mule and Ghost Controls units when factory parts are back-ordered. Most brand-specific repairs in Kensington are completed on the first visit because our trucks carry the inventory.
Common Gate Parts & Welding Problems We See in Kensington Homes
- Freeze-thaw masonry damage. NYC’s winter temperatures regularly cross the freezing mark multiple times, causing mortar in stoop-embedded gate posts to crack and shift. This misaligns hinges and makes gates drag seasonally, often worse in March after the heaviest freeze cycles.
- Obsolescence of original hardware. The forged-iron hinge pins and hand-forged latches on 1920s Kensington gates haven’t been manufactured in decades. When they fail, the choice is custom fabrication or a mismatched modern replacement that compromises the gate’s appearance and function.
- Shared-gate complications. On semi-detached rowhouses, the side-yard gate is often the only access point for two separate households. When it fails, both are affected, and repair urgency is high. We’ve mediated more than one repair where landlord-tenant responsibility was disputed; we document the condition and provide a written estimate both parties can use.
- Salt corrosion on original iron. Brooklyn sidewalk salt accelerates rust on wrought-iron hardware in ways that interior or suburban gates don’t experience. We see this most on lower hinge pins and latch mechanisms that sit below the salt-splash line from passing foot traffic.
Pricing for Gate Parts & Welding in Kensington, NY
Here’s what typical gate parts and welding work costs in Kensington’s market:
| Service | Typical Range |
|---|---|
| Hinge replacement (single) | $180 - $320 |
| Post repair / steel sleeve | $280 - $480 |
| Custom welding, rail or scrollwork | $340 - $650 |
| Latch and lock replacement | $150 - $280 |
| Roller replacement (sliding gate) | $200 - $350 |
| Seasonal adjustment and lubrication | $89 - $140 |
What moves a job toward the higher end: obsolete parts requiring custom fabrication, masonry repair to stabilize a post, or access complications on shared gates where both households must coordinate. We settle on an upfront price before any work begins. Our $89 Seasonal Tune-Up catches many of these problems before they become expensive repairs. Senior and veteran customers receive 5% off any service, always. Call (877) 326-7055 for a free estimate - we’ll give you an exact number, not a guess.
We Also Serve Cities Near Kensington
Our Gate Parts & Welding in Kensington service extends to neighboring Brooklyn communities. We regularly work in Flatbush on similar 1920s rowhouse ironwork, Borough Park on heavier synagogue and institutional gates, Park Slope on brownstone-era pedestrian gates, and throughout Brooklyn on driveway and estate gate systems. The same 90-Day Done Right Promise and live-answer phone line cover every neighborhood we serve.
Serving Kensington, NY - Our Local Coverage Area
We’re based in the Kensington area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Parts & Welding in Kensington
We usually fabricate a replacement rather than find one, because the forged-iron hinges on 1920s Kensington gates haven’t been manufactured for decades. We worked on a 1920s semi-detached rowhouse on Beverley Road where the original wrought-iron side-yard gate had a seized hinge from decades of freeze-thaw cycling. The hinge was an obsolete forged-iron design no longer made, so we custom-welded a new pivot pin and reinforced the post with a steel sleeve set in epoxy, restoring function for both households that share that passage. The gate still had its original lift-master style handle, which we kept. If your hinge is seized, call (877) 326-7055 - we can typically restore operation without replacing the entire gate.
Responsibility depends on your lease terms and whether the gate serves a single unit or common area, but we can help clarify the situation quickly. We document the gate’s condition with photos and a written estimate that both parties can review, and we’ve handled many Kensington repairs where landlord-tenant coordination was needed. Our background-checked, uniformed technicians are trained to work professionally in multi-household situations. Call (877) 326-7055 and we’ll assess the gate and provide documentation you can use to resolve responsibility.
Yes, in most cases we can weld cracked scrollwork in place using portable TIG equipment with color-matched filler rod that blends with aged iron. Removing a century-old gate integrated into Kensington stoop masonry risks damaging both the gate and the brickwork, so we avoid it when possible. The weld repair typically takes 2-3 hours and costs $340-$650 depending on access and pattern complexity. Call (877) 326-7055 for a free assessment - we’ll tell you if in-place welding is viable for your specific gate.
Dragging after winter usually indicates masonry post shift from freeze-thaw cycling, not hinge failure, though the two often occur together. We can often correct minor drag with hinge adjustment and post stabilization, but if the post has shifted significantly, a steel sleeve or post repair is needed to prevent recurring problems. Our $89 Seasonal Tune-Up includes hinge adjustment, hardware lubrication, and post inspection - it’s the best first step. If parts are needed, we’ll show you exactly why before any replacement. Schedule at (877) 326-7055.
We stock legacy components for many discontinued LiftMaster, DoorKing, and Elite systems, and we can often source or fabricate alternatives when factory parts are unavailable. For Kensington’s older housing stock, this is a common request. If we don’t have the exact part, we’ll retrofit a compatible latch that maintains your gate’s security and function. Latch replacement typically runs $150-$280. Call (877) 326-7055 with your model number - we’ll know immediately what we can do.
Written by Frank Delmonico, Owner at Ironworks Gate Co., serving Kensington since 1984.