Linear Gate Parts & Welding in New York City, NY

Linear Gate Parts & Welding in New York City: What to Know First

We provide independent Linear gate parts and welding service across New York City, typically completing hinge replacements, post repairs, and rail welding in a single visit with upfront pricing agreed before we start. Most Linear gate jobs run $280 to $750 depending on the part and access, and we carry common Linear hardware on our trucks for same-day resolution. This page is for homeowners in the five boroughs who own a Linear automated gate system and need metalwork done right - not patched, not rigged, but fixed so the motor isn’t straining against bent rails or sagging posts six months later. Call (877) 326-7055 and a live person will answer, 24 hours a day.

Call (877) 326-7055

How Linear Products Fail - and How We Fix Them

• Linear Pro Access control arms with cracked hinge brackets. The Pro Access series uses cast aluminum hinge brackets that fatigue where they meet the steel gate frame, especially on heavy iron driveway gates common in Queens and Brooklyn. We fabricate a steel reinforcement plate, weld it in place, and relocate the load so the bracket stops cracking. A bracket replacement alone without the weld reinforcement usually fails again within two years.
• Linear SLR sliding gate posts that lean on tight New York lots. The SLR line puts significant lateral load on the receiving post during open and close cycles, and in Manhattan and Brownstone Brooklyn where setbacks are minimal, that post often sits in disturbed soil from prior construction. We pull the post, pour a new concrete footing below the frost line, and weld the SLR track mounting tabs square - not shimmed, not wedged, square.
• Linear LSO swing gate rails that rack out of plumb. The LSO series depends on perfectly parallel top and bottom rails; when a vehicle bumps the gate or the hinges settle, the rail gap pinches the operator arm. We straighten the rail in place or cut and re-weld the rail joint, then reset the LSO arm geometry so the limit switches stop hunting for position.
• Linear actuator mounting plates torn from wrought iron frames. Linear actuators mount through a single bolt pattern that concentrates stress on decorative wrought iron gates popular in Staten Island and the Bronx. We weld a spreader plate across multiple pickets to distribute the load, then remount the actuator. The factory plate bolts through one tube; our welded spreader ties into three.
• Linear gate rollers ground flat on sloped driveways. In hilly parts of Riverdale or Inwood, Linear sliding gates often use V-groove steel rollers that wear eccentric when the track settles. We replace with sealed bearing rollers, weld track shims where the concrete has shifted, and adjust the Linear motor clutch so it doesn’t compensate by over-torquing.

Our Linear Gate Parts & Welding Process

1. 1
   Call and describe the gate. A live person answers, notes your Linear model if you know it, and schedules a visit. We ask about gate material, approximate age, and whether the motor runs but the gate won’t move.
2. 2
   On-site diagnosis. Our tech inspects the mechanical system before touching the Linear operator - bent rails, loose posts, worn hinges, cracked welds. The motor is usually fine; it’s the metalwork that failed.
3. 3
   Parts decision. We stock common Linear hinges, rollers, and mounting hardware. For proprietary Linear components, we source OEM or match a quality aftermarket part that won’t void your operator warranty. We explain the choice and the price before ordering.
4. 4
   The repair. Welding is done with the gate supported, not hanging free. We grind old welds clean, prep the joint, weld, and prime same-day. No gate leaves your property.
5. 5
   Test and adjust. We cycle the Linear operator through full open and close, check limit switch alignment, and verify the motor current draw isn’t spiking against new resistance.
6. 6
   Cleanup and guarantee. We leave the work area as we found it. Your repair is covered by our 90-Day Done Right Promise - written, no paperwork, no arguing.

What Linear Gate Parts & Welding Costs in New York City

Prices include labor, parts, and the 90-Day Done Right Promise. We do not charge diagnostic fees when you proceed with the repair. Call (877) 326-7055 for a free estimate - we’ll give you a firm number before any work begins.

Why New York City Homeowners Call Ironworks Gate Co. of New York City for Linear Work

We’ve been repairing gates across the five boroughs since 1984. Frank Delmonico started this company after studying welding at New York City College of Technology and working alongside the old tradesmen in Sunset Park industrial yards. That background matters when your Linear gate needs metalwork, not just a keypad reset.

Our techs are trained on nine automation brands - Linear, LiftMaster, Mighty Mule, Ghost Controls, DoorKing, plus FAAC, BFT, Viking, and Elite - so if your operator has a secondary issue, we fix it on the same visit. Most jobs finish in one trip. A live person answers the phone at midnight on Saturday. And the 90-Day Done Right Promise applies to every weld, every part, every adjustment - written, no hassle, no exceptions. A gate that works quietly is a gate that’s been done right.

FAQs